TransformationofElectrocompetentE.coliwithBlue／Whiteselection

1. Desalt DNA template by EtOH precipitation in NaOAc followed by at least 2x washes with 70% EtOH.  Resuspend in 5 - 15 µL of sterile H₂O.

2. Rinse cuvettes (if they have been used before) 5x with deionied H₂O, and place them on ice.  This is sufficient to avoid background growth in most cases.

3. Set a BioRad MicroPulser to "Ec1" for 1 mm cuvettes, or "Ec 2" for 2 mm cuvettes.

4. Electroporate the DNA into the bacteria:

1. Add 5 µL of DNA to 50 µL of bacteria and mix by pipetting.

2. Transfer bacteria/DNA mix to a cold cuvette, and immediately pulse in the electroporator.

3. Quickly add 1 mL of r.t. L.B. to the bacteria in the cuvette.  Use a sterile Pasteur pipette to transfer the suspension to a bacteria tube.

4. Repeat for additional DNA samples and control DNA.
   

5. Rotate at 37ºC x30 min. to allow the bacteria to recover. 
   

6. Meanwhile plate LB/Amp plates with IPTG + X-gal if blue/white selection of colonies will be performed, as follows:

1. Mix 100 µL X-gal + 20 µL of IPTG per plate.

2. Spread X-gal/IPTG mix across surface of plate with a sterile glass spreader and a plate spinner.  
   

3. Allow the mix to infiltrate the media for 20 min. 
   

7. Perform two 10-fold serial dilutions of the LB/bacteria suspension into fresh sterile L.B.  Concentrate the remaining bacteria by spinning 1 min. at 5k rpm in a sterile microcentrifuge tube, and then resuspend pellet in 0.1 mL of L.B.  
   

8. Plate 100 µL of the various concentrations of bacteria onto LB/Amp (+ X-gal/IPTG as necessary), and spread with a sterile spreader and plate spinner to evenly coat the plate.  Record the DNA construct and the Bacteria Dilution Factor (9x, 1x, 1/10x, 1/100x) on each plate. 
   

9. Incubate the plates inverted at 37ºC o.n.  They may need to be placed in a container if the humidity of the incubator is so low that it causes the agar to dry out.  
   

10. Remove the plates when the colonies are ~1mm in diameter.  The color development on X-gal treated plates will continue to occur after the plates are removed from the incubator.

11. Pick white colonies (also with no central blue coloration) and restreak on L.B./Amp plates to ensure that pure clones are obtained before performing plasmid preps. 
    

12. Store at 4ºC for at least 1 hr. (to firm up the agar) if colony hybridiation will be performed.  Seal edges of plates with parafilm for storage up to 1 week.

13. Count the numbers of colonies on the plate with control DNA to determine the efficiency of competent cells:

1. Efficiency (Transformants/µg) =  colonies/plate x (Bacterial dilution factor) x  20,000

2. Highly competent cells should have ~50 colonies on the plate with a 1/10 dilution of the control DNA's bacteria suspension.
   

Materials

• Control DNA (e.g. pBS) diluted to 1 pg/µL in sterile H₂O, on ice.
  Electrocompetent bacteria, frozen (50 - 100 µL aliquots), on ice.
  BioRad cuvettes (1 mm gap), on ice.  
  Sterile L-Broth (L.B.) 
  Bacteria culture tubes
  

• P1000, P200, P20 Pipetman and sterile tips
  Sterile Pasteur pipets and bulb.
  37ºC incubator and rotating wheel
  L.B./Amp bacterial culture plates (or other suitable selection media)

• X-gal 20 mg/mL in DMF (dimethlyformamide), store at -20ºC
  IPTG 0.2 g/mL in H₂O, store at -20ºC