实验概要
This method is use to extract short RNAs from plant tissue. Some of the variables (e.g. centrifugation speeds×, precipitation times and volumes of ethanol) have not been optimised: the conditions given here work but I’m sure some streamlining is possible. There are three main steps: extraction, size fractionation, and final clean-up.
实验原理
We originally estimated the size of the PTGS specific RNAs to be 25 nucleotides. I¹ve found recently that like those in Drosophila cell there are actually two main species. In most plant silencing examples we¹ve looked at the smaller of the two is much more abundant and initially I thought that the upper band was simply the trailing end of the lower one. With some new systems we've been looking at the upper band is much more pronounced relative to the lower and so its presence is much clearer.Using RNA markers instead of DNA oligos and with the extraction protocol outlined below the upper band runs at 25nt and the lower at 23 nt. this is still two nucleotides larger than the Drosophila RNAs (21-23). However, when I gel purify the "25" and "23" and re-run them, they run faster: two nt faster in fact! I¹ll continue to refer to these as 25nt RNAs below for convenience.
25nt RNAs can be detected from total RNA preparations (i.e. without enrichment) in some cases. It depends on how clean your (this depends of course on the plant type and extraction method)is and the strength of the PTGS you are studying (stronger PTGS means more 25nt RNA and therefore higher signal:noise). The choice is yours! Enrichment for low mol.wt. RNA from total RNA preparations improves the ease of handling and allows proportionally more to be analysed per assay than using total RNA. Also, too much high molecular weight RNA and DNA in the samples tends to cause drag during the run. Most of the types of plant tissue I have used contain carbohydrates which co-purify with RNA under most conditions and so I almost always take steps to remove these. The DEAE step (step3) is also quite effective at removing polyphenols that co-purify from some plant tissue.
主要试剂
SDS based extraction solution [ Details:see Science paper]
实验步骤
1. Start by extracting RNA as you would for total RNA: I use the SDS based extraction solution (see Science paper) but others work too (e.g. GITC (guanidine isothiocyanate), Kirby’s) and may even be superior. I do two phenol/chloroform extractions of the slurry followed by precipitation with ethanol (3 vol) and NaOAc (0.1 vol) for at least two hours at -20. This is the basic total prep. Don’t use silica based columns (e.g. "RNAeasy") because the short stuff doesn’t stick. Recover the total RNA/DNA by centrifugation as you would normally (e.g. 10000xg/20 min). If the ppt looks clean enough you could try going straight to the Northern (after UV quant. of course).
2. This next step is to remove the majority of the high molecular weight nucleic acid. I’ve used several methods for this but this one is the simplest and cheapest and may provide a low mol. wt. fraction that is clean enough to use directly. I stopped using centricon filtration because I found that their performance seemed compromised with extracts from Nicotiana species. Another way I tried briefly was to use GITC extraction solution, spin down debris, add 1/2 vol ethanol to s/n and apply to a silica column (Supelco). This column bound all the RNA and DNA bigger than about 200nt. I Phenol extracted the flow through, EtoH pptd, and purified the lowMW RNA in the redissolved pellet away from the contaminating carbohydrate by DEAE chromatography as below. This way was a bit wasteful because of the large amounts of GITC solution and phenol/chloroform I had to use so I did not pursue it.
My current favourite method is as follows. Dissolve the pellet in water/TE (volume depends on size of pellet; usually I use between 0.5 to 5 ml). I heat this to 65 C to disrupt any association of the 25nt RNA with the larger RNA and DNA molecules and it also quickens the dissolving of the pellet. Place on ice and add PEG (MW=8000) to a final conc of 5% (I used to use 10% but 5% is safer: less chance of small stuff co=precipitating with large stuff) and NaCl to a final conc of 0.5M. Mix well, and leave on ice for 30 mins. Spin down at 10000xg for 10 mins which will pellet the high molecular weight nucleic acid. KEEP THE SUPERNATANT: this contains mainly tRNA and small rRNAs but also the 25nt RNA. I also normally dissolve the pellet of high mol.wt RNA/DNA in formamide to compare with the subsequent low mol. wt. fraction in order to asses the separation. Can also use this for conventional Northerns etc..
Add three volumes of ethanol to the supernatant of the PEG pptn and place at -20 for at least two hours. Spin down at 10000xg for 10 mins. This ppt. comprises mainly tRNA and small rRNA and will run as a thick band around 100-200bp on a non-denaturing mini-gel (e.g. one routinely used for plasmid analysis). The high mol.wt. fraction (if you run it !) will of course smear upwards from this. As I said, if the LMW fraction is clean enough, I dissolve this in formamide and use it directly for Northern blots. I quantify the low mol. wt. fraction either by taking aliquots and measuring UV absorbance (after ethanol pptn to remove the formamide) or by quantifying the fluorescence after EtBr staining of the minigel. With Nicotiana species (for example from N. Benthamiana), I get a lot of jelly like material (I thought this was likely to be pectins but was assured by a cell wall expert that that was very unlikely, so I don’t know what it is but its not RNA!) which causes difficulty in handling and the RNA does not run well on the gel and so I purify further as follows.
3. I've recently started to use DEAE-sepharose CL-6b (Sigma) in preference to Qiagen columns since it is cheaper. Equilibrate the sepharose in buffer A (50mM MOPS/NaOH pH7; 15% isopropanol; 0.2M NaCl; 0.15% Triton x-100) I make quick columns with this by cutting some whatman 1 filter paper circles small enough to plug the end of a 5ml disposable syringe, adding 1ml of the equilibrated sepharose and letting the column settle. Redissolve the ethanol ppt’d low mol. wt. fraction in buffer A and apply to column under force of gravity only. Or..you can skip a step by adding water to the supernatant of the PEG pptn (section 2 above) until the NaCl concentration reaches 0.2M and then adding 5-10 volumes of bufferA and applying this to the column. Collect the flow-through and reapply to column. Wash the column with more bufferA (I do 10 column volumes) and elute with buffer B (same as bufferA except NaCl concentration is 1.0 M). Add three vol of ethanol directly to this eluate and place at -20 for at least two hours and after a 10000xg spin for 20 mins and a 70% ethanol wash, I dry the pellets and redissolve them in formamide (Usually 100-1000ul).
NORTHERN BLOTTING FOR LMW RNA
Gel: 15% polyacrylamide (19:1); 7M urea; 0.5xTBE. I use Biorad "protean" apparatus = a vertical 500pxx500px glass plate gel sandwich with 1.5mm spacers and a "castellation" type of comb.
Since the samples are already in formamide, I heat these to 65 C for 5 mins, place on ice, add 1/3 volume of 4xloading solution (= 2xTBE, 40% sucrose, 0.1% bromophenol blue). I use anywhere between a few hundred to 50ug of RNA per lane.
Run the gel in 0.5 x TBE at 100-500V until BPB is almost at the bottom (usually 2-6 hours). Separate sandwich and place gel on a prewetted (0.5xTBE) piece of HybondNX hyb¹n membrane. I use a BIoRad "wet" electroblotter to blot the RNA. I give it about 45 minutes at about 100V in 0.5 xTBE. I used to use 33P kinased DNA oligos or DNA homologous to your probe digested with a frequent cutter to give size markers. I now use 32P labelled in vitro transcribed RNA which has been fully RNAaseT1 digested. After the blot, I place the membrane on several layers of filter paper soaked in 20 xSSC to equilibrate the membrane. I don¹t let the solution of 20xSSC flood over the membrane surface because I¹ m worried that at this stage, prior to fixing, the attachment of such small molecules to the membrane may not be particularly strong (this could be a bit paranoid). After about 30 minutes, dry the membrane thoroughly (e.g. in oven if you want). I then fix in a Stratalinker (autocrosslink setting). Store membrane in dark until use.
Prehyb membrane in
50% formamide; 7% SDS; 50mM NaHPO4/NaH2PO4 (pH7); 0.3M NaCl; 5x Denhardt¹s sol¹n; 100ugml-1 sheared, denatured salmon sperm DNA, at 40 for at least half an hour.
Probes: I use single stranded, 32P labelled RNA probes transcribed in vitro from plasmid templates. Initially, you should use the whole length of the sequence undergoing PTGS since the 25nt RNA may not be derived from the entire sequence. E.g.: In GUS PTGS, most of the signal comes from the 3¹end of the GUS gene. Make the probe as you would for a normal Northern. The specific activity is up to you but remember if you use too little of your limiting NTP you may have underrepresentation of you probe at its 3¹ end especially with longer probes. I remove the DNA template by adding RNAase-free DNAase directly to the transcription reaction. and continuing the incubation at 37 for an hour. Then I hydrolyse the probe. This is very easy and the benefits are that I get less background and also the membranes strip very easily. Make up a 200mM solution of carbonate buffer as follows: 80mM NaHCO3 (0.672 g per 100 ml) 120mM Na2CO3 (1.277 g per 100 ml). If you have done the transcription in 20ul, add 300ul of carbonate buffer and incubate at 60 for as long as it takes to reduce the probe to an average size of 50-100 nucleotides. Use this formula to calculate the time
t= (Li - Lf)/(k.Li.Lf)
where
t = time in minutes
Li = initial length of probe in kb
Lf = final length of probe in kb (i.e 0.05 in our case)
k = rate constant = 0.11 kb. min-1.
It usually takes 1-3 hours for the hydrolysis. Add 20 ul of 3M NaOAc (pH 5) to the reaction and then add all of this to the hyb solution. Hyb at 40 degrees C overnight, wash at 50 in 2xSSC/0.2% SDS. The strength of signal of course depends on how much you load etc.. but I normally get a clear picture after an overnight exposure with screens at -70. Patchy background can arise from using too much probe: if you saved your probe, simply strip the membrane (1 minute at 90 C in 0.2%SDS, 10mM Tris/HCl pH7.5 usually completely strips these filters including background), re-pre-hyb, add some of the hyb solution containing probe back and leave to hyb again.
注意事项
There appears to be some confusion arising from the way we have described the protocol in the Science and Plant Cell papers.I hope the following clears up any problems you have.
My "Science" paper mentions using using ion exchange with Qiagen columns to clean RNA preps up. I was referring to the original Qiagen support which is a modified DEAE and a bona fide ion exchanger. I now use DEAE sepharose which is cheaper and quite fine for separating small nucleic acids. The modified DEAE of Qiagen was, I think, the product upon which the Qiagen company was founded (the modification they made made it possible to use DEAE for separating much larger nucleic acids such as plasmids hence the success of the company). More recently Qiagen (along with some other companies) have introduced silica based RNA purification kits. This idea is just an extension of original observations years ago that DNA binds silica (the basis of "Geneclean" gel purification kits). These were never much use for RNA until it was noticed that you could get RNA to bind to silica by adding ethanol to the mixure of silica, chaotropic salt and RNA. I don't know who owns the IP on this but I don't think Qiagen invented it. At any rate they now produce these silica based purification kits which are fine for mRNAs. However, as we say in Tamas' "Plant Cell" paper, the short RNAs do not stick to these. They are not really ion exchange columns so it should have been possible with very careful reading of the two papers to work it out but I do see how the confusion has arisen.
日,《科学通报》在线发表了华南农业大学园艺学院教授夏瑞团队最新研究成果,他们研究开发出一款多功能植物小RNA分析工具——sRNAminer,可便于研究人员进行一站式小RNA分析及可视化。据介绍,植物小......
RNA干扰是指由双链RNA诱导的基因沉默现象,在细胞发育和抗病毒免疫等生物学过程中发挥重要作用,并被用作基因功能研究和疾病治疗的遗传工具。RNA干扰现象可在秀丽隐杆线虫全身及其后代中传播,被称为系统性......
生物体的复杂性是由它们的基因编码的,但这些基因从何而来?据最新一期《美国国家科学院院刊》报道,芬兰赫尔辛基大学研究人员解决了围绕小分子RNA基因(microRNA)起源的悬而未决的问题,并描述了一种创......
11月30日,中国科学院生物物理研究所叶克穷课题组在《中国科学:生命科学(英文版)》(ScienceChinaLifeSciences)上,在线发表了题为Complicatedtargetrecogn......
近日,中国科学院水生生物研究所张承才团队关于细菌中RNA代谢调控机制的研究取得了进展。相关研究成果以《蓝藻中RNaseE受一个保守蛋白调控》(Aconservedproteininhibitorbri......
应激颗粒是在胁迫条件下形成的动态结构,通常认为其中包含翻译被抑制的RNA以及翻译元件,并可在刺激消失后解聚,是细胞内典型的无膜细胞器。在应激颗粒组装的不同阶段,大量RNA分子会被招募至应激颗粒中,对维......
2023年11月21日-22日,国家自然科学基金委员会(以下简称自然科学基金委)第357期双清论坛“RNA与重大疾病诊疗”在杭州召开。本次论坛由自然科学基金委医学科学部、生命科学部、化学科学部和计划与......
11月24日下午,闵行区人民政府、中国科学院分子细胞科学卓越创新中心以及上海交通大学在闵行区大零号湾科创大厦共同签署了战略合作协议。此次合作的核心内容是,核糖核酸功能与应用全国重点实验室(筹)将落户在......
RNA编辑广泛存在于植物的线粒体和叶绿体中。RNA编辑作为一种RNA转录后加工机制,对于调控基因表达具有重要意义。RNAC-U的编辑是胞嘧啶(C)经过脱氨转变为尿嘧啶(U)的过程。在此过程中,PPR(......
RNA表观遗传学为基因表达调控提供了一个新的切入点,以RNAm6A甲基化修饰为代表开辟了RNA表观遗传的研究新方向。首个m6A去甲基化酶FTO的发现证实了m6A修饰的动态可逆性,成为推动m6A领域发展......